Isn't it great how fashionable patches on leather jackets can be? With only a few words, you can give a brief introduction to the people you meet. The nicest aspect is that leather jacket patches can be easily sewn on.
It's simpler to stitch patches using a sewing machine than it is to do so manually. As a general rule, you'll sew until the start and final stitches of the patch meet. To make it look good, though, you need someone who knows how to sew.
No worries! In this post, we'll be taking you through the step-by-step process of how you can get patches sewn on leather jacket and where you can have them custom-made.
1. Have a sewing machine
Have a sewing machine made for leather
Rather than attempt to sew through leather by hand, it is highly suggested that you use a sewing machine. Therefore, you should get a sewing machine designed for leather. Most industrial sewing machines are capable of properly accomplishing the task.
Sewing machines that are regarded as industry standards are not powerful enough to complete the task. Sewing machines and leather working equipment specialty shops are your best bets for finding the exact machine you're searching for. It's also possible that you may get such a machine online.
2. Choose an 18-Gauge Needle
Choose an 18-Gauge Needle and a Wide Stitch
Begin by choosing a wide thread width, an 18-gauge needle, and set the sewing machine to go. The needle must be inserted into the sewing machine at this point. Changing the stitch width from its default value of 0.32 millimeters (1/8 inch) to the broadest possible value is the next step.
When stitching with an upholstery needle, use upholstery thread, which might be polyester or nylon depending on the manufacturer. Using a needle made particularly for leather may provide the greatest results. Even if you can't, you should at least make sure that the needle is thick and sharp.
3. Apply Adhesive Spray
Adhesive spray should be used to attach the patch to the garment's back. Put a good ten to fifteen centimeters (4 to 6 inches) of the distance between the can of spray adhesive and the patch you're working on before shaking it.
The amount of glue required for this project is really little. To complete the process, all that is needed is a sprinkle of glue. Because the adhesive's only purpose is to keep the patch in place during stitching, you don't need a lot of it.
When a spray adhesive is not available, you may either use a standard glue stick or a little amount of rubber cement to complete the job. Neither of these choices is a bad one. To prevent the holes in the jacket from becoming permanent, please dispose of the sewing pins immediately once you have finished using them.
4. Put the Patches at Your Chosen Spots
Determine where you want the patches to go, and then make your decisions based on that information. At this stage, it's time to sew the patches on the clothing. Review instructions to see whether or not you must wait for the glue to dry completely before continuing.
Apply a little amount of pressure to the patches until you feel that they are firmly attached. Use the seams of the jacket as a reference point when deciding where to place patches on the jacket.
5. Sew the patches
From this stage, you have the option of beginning the stitching procedure at any of the patch's four corners. Attempt to keep your stitches as near as possible to the embroidered edge of the patch as you work on it. In addition, you'll need to keep a low speed and be very cautious through the tight turns.
Because of this, it is best to begin lowering the needle as soon as you reach a tough angle or corner. Pulling the jacket up to your chest is the next step, followed by a turn. You may restart sewing after successfully repressing your foot into the floor. If the vest has a lining, be sure to smooth out the jacket lining before moving on to the vest.
6. Tuck in the first and last stitches
A minimum of one to one and a half inches is required between the first and final stitches (or 2.6 to 3.9 cm). Continue sewing for an extra inch and a half or an inch after you finish the first round of stitches and return to the starting point.
If you do this, you will prevent the fabric from unraveling at the beginning and conclusion of the project because of the overlap of one to one and a half inches. Not to mention the fact that you won't be burdened with backstitching. Because of this, you won't have to deal with any inconveniences.
7. Cut the thread
Cut the thread after pulling out the leather
To reassemble your jacket, cut the thread that holds it together once you remove it from the machine. Remove the needle and the foot from the jacket before pulling up. Take the jacket out from below the foot and cut the thread as close to the path and the lining as possible.
There you have it! Now that you have an idea of how to sew a patch on your leather, sewing can be an easy task next time. However, if you still find it hard to make it look perfect or up to your taste, you can ask for help from Palaleather and have your leather custom-made. Just visit their website at www.palaleather.com and enjoy their one-of-a-kind designs!